Epson Stylus Color 800
Product Controls: Epson Stylus COLOR 800
Cleaning Cycle Black - Black Cleaning button
Cleaning Cycle Color - Color Cleaning button
Printer's Self-Test (LQ) - Load/Eject + Power-On
Printer's Self-Test (draft) - Black Cleaning + Power-On
Hex Dump Mode - Load/Eject + Color Cleaning + Power-On
Default Setting Mode - Color Cleaning + Power-On
First Ink Cartridge Installation (takes approximately 7 minutes) - Turn the printer on and the print head will automatically move slightly to the left. Remove the yellow tape seal from each ink cartridge. Do not remove the white label from the top of either ink cartridge. The ink in a cartridge missing the white label will be exposed to air and will thicken such that print head clogging and possible print head failure can occur. If the white label has been removed from an ink cartridge, the cartridge will not function correctly and it will need to be replaced. More importantly, to avoid potential damage to the printer, do not install a cartridge from which the white label has been removed. Install the black and color ink cartridges, then press the load/eject button to begin charging the ink delivery system.
Install Replacement Ink Cartridge when an ink out condition occurs - Remove the yellow tape seal from the ink cartridge you are going to install. Do not remove the white label from the top of the ink cartridge. The ink in a cartridge missing the white label will be exposed to air and will thicken such that print head clogging and possible print head failure can occur. If the white label has been removed from the ink cartridge, the cartridge will not function correctly and it will need to be replaced. More importantly, to avoid potential damage to the printer, do not install the cartridge if the white label has been removed. If the black ink out light is flashing or solid, hold the black cleaning button until the print heads move to the left, and then install the black ink cartridge. If the color ink out light is flashing or solid, hold the color cleaning button until the print heads move to the left, and then install the color ink cartridge. After installing the cartridge, press the load/eject button to begin charging the ink delivery system.
Why can't I print from a particular Windows application in color?
Make sure the correct driver is selected and the Color option is enabled in the printer driver. Try printing again. If the image comes out monochrome, print from a resident program within Windows, such as Paintbrush. If the results are successful from Paintbrush, contact the software manufacturer of the application for assistance. If the results are not successful, troubleshoot the pertinent areas within Windows, such as the video driver.
Why are some characters incorrect or garbled?
Make sure you are using the correct driver. Select the Stylus Color 800 as your default printer driver. Check to see if there are any stalled print jobs in the Spool Manager. Delete all stalled jobs and resume printing. The interface cable may not be securely connected. Turn off the printer and computer. Disconnect and reconnect the cable on both the printer and computer. Make sure the printer is cable is fully-shielded and meets the printer's specifications.
What are the Epson Spool Manager and Epson Despooler?
The Epson Spool Manager manages special spool files called "journal" files. These contain the print data in an unprocessed form. The Spool Manager sends this data to the Epson Despooler for processing. The Despooler processes the data in segments, called "bands". Once a band is finished, it is sent to the printer for printing. While the printer prints, the Despooler works on the next band.
What are the minimum requirements to use this printer with a PC?
You will need an IBM compatible PC with at least a 386/25 MHz or faster processor, Microsoft Windows 3.1/Windows for Workgroups 3.1/Windows 95 or 98, at least 8MB of RAM (more for Windows 95 or 98), at least 20MB of free hard disk space for storing images (40MB or more is recommended), VGA/Super VGA or better display adapter and monitor, a shielded twisted-pair parallel cable (6 to 10 feet long).
I do not have the Stylus COLOR 800 as a driver selection in my DOS application. Which printer should I select?
For color output choose the Stylus PRO, Stylus COLOR 500, Stylus COLOR II, LQ-2550, or LQ-860. For monochrome (black/white) printing select one of the following LQ or SQ models: LQ-870/1170, LQ-570+/1070+, SQ-870/1070, LQ-850, OR LQ-500.
How do I install the driver in Windows 95 or 98?
Insert the EPSON printer software CD in your CD-ROM Drive. If Windows 95 or 98 launches the install program automatically, click on the Install button. If the installer does not launch automatically, click the Start button and select Run. Type D:\EPSETUP and press Enter. Select the Epson Stylus COLOR 800 then click OK. The installer creates an EPSON folder for your printer software icons, adds an icon for your printer to the printers folder, and makes your printer the Windows default printer.
I have a picture of the printer (the Despooler) with the International NO symbol across it on my screen. How can I clear this?
Check the Spool Manager to make sure the correct settings are enabled. Check to see if the Spool Manager is Held. Delete any queued print jobs and remove the check mark from the word "Hold" under the Queue menu. Make sure there is paper loaded in the printer and try printing again.
When I print from Windows 3.1x, I'm getting the message "Disk is full" on my PC screen. How can I clear this?
In the Program Manager, go to Control Panel, select Printers. If you are printing to LPT1.DOS, change the port setting to LPT1:Local port. Check to see if there are any stalled print jobs in the Spool Manager. Delete any stalled print jobs. Create a new unique directory on your hard drive, such as C:\SPOOL. Open the Spool Manager and make sure the EPSON Stylus COLOR 800 is selected. Click on Options, select Default Spool Directory. Change the directory to the new directory you created and click OK. Open the Queue, Setup and make sure the spool directory changed to the new unique directory. Make sure the box for "Use Print Manager for this port" is not checked, then click OK. Close the Spool Manager, restart the computer and try printing again.
My printer's control panel locks up after I print a document from Windows. The buttons on the panel do not respond unless I disconnect the parallel printer cable from the back of the printer. What's wrong?
Some computers send an initialize/reset signal during the boot-up process. If the printer cable picks up any noise during this process, the initialize line will not complete its reset phase and cause the control panel to lock. Try booting the computer to Windows, then turn the printer ON using the printer's power switch and try printing again. A defective cable can also cause this situation. Make sure you are using a fully-shielded parallel cable, preferably 6 feet or less.
Why doesn't the Status Monitor box in Windows 95 or 98 appear with the Despooler?
The Windows Print Manager may be interfering with the Status Monitor. Open the Spool Manager and make sure the EPSON Stylus COLOR 800 is selected. Click on Queue, Setup and make sure the box for "Use Print Manager for this port" is not checked, then click OK. Close the Spool Manager. Next, click Start, select Settings, Printers. With your right-mouse button, click on the EPSON Stylus COLOR 800 icon and select Properties. Click on the Details tab, click on the Spool Settings button and make sure the Enable bi-directional support for this printer option is turned on, then click OK. The Status Monitor should now appear when you send your next print job.
Are there drivers for Windows NT 3.51 or 4.0?
Yes, for Windows NT 3.51 use the file C8N3101A.EXE disk version 1.01A. For Windows NT 4.0 use the file C8N4101A.EXE, disk version 1.01A. The driver is available for download from the EPSON Internet website.
I'm getting an error, "Encountered error while processing band data, spool file is corrupt." How do I clear this?
If you are using Print Shop Deluxe, choose File, Preferences from the Print Shop menu and remove the check mark from "Fast Bitmap Printing." Check the Spool Manager to make sure the correct settings are enabled. Check to see if the Spool Manager is Held. Delete any queued print jobs and remove the check mark from the word "Hold" under the Queue menu. Make sure there is paper loaded in the printer and try printing again. If you get the same error message, reinstall the printer driver and try printing again. If the condition persists, obtain a replacement printer driver available for download from the EPSON's Internet Web Site.
Why do I see a New Hardware found window after installing the printer software into Windows 95 or 98?
An operating system error has occurred. Click Do not install a driver, then click OK. Windows will not prompt you with this error again.
When I try to print in Windows 95 or 98, the message "The printer is out of paper" or "The printer is off-line" appears in the despooler. What do I do?
Examine the printer's control panel to make sure the printer does not show a paper out error. Try printing the directory from DOS. Type "dir>prn" from the DOS prompt. If this does not print, make sure the printer cable is securely connected. A defective cable can also cause this problem. Make sure you are using a fully-shielded parallel cable, preferably 6 feet or less. If the DOS test printed, open the EPSON Spool Manager, open the Queue, select Setup and change the setting (check or uncheck the box) for "Use Print Manager for this port". Close the Spool Manager, restart the computer and try printing again. In Windows 95 Spool enable the setting "Print directly to the printer" and disable any options in the Port settings. If there is still an error, please contact the EPSON Connection for assistance.
Why doesn't the Status Monitor show the ink levels in Windows 95 or 98?
The Windows Print Manager may be interfering with the Status Monitor. Open the Spool Manager4 and make sure the EPSON printer is selected. Click on Queue, Setup and make sure the box for "Use Print Manager for this port" is not checked, then click OK. Close the Spool Manager. Also, the parallel cable should be IEEE-1284 compatible for the Status Monitor feature to function.
How do I install the printer driver in Windows 3.1x?
Insert the EPSON printer software CD in your CD-ROM Drive. From Program Manager, click on File, then select Run. At the Command Line type D:\EPSETUP and press Enter. Click the Install button. An EPSON Stylus Color 800 icon will appear. Click OK to install the printer driver. The installer creates an EPSON group for your printer software icons and makes your printer the Windows default printer.
How do I install a printer driver on a Macintosh?
Start or restart your Macintosh with all Extensions OFF, except the "Apple CD-ROM" extension. Before installing the driver, go to the Chooser, ensure AppleTalk is inactive, then close the Chooser. Insert the CD into your CD-ROM drive. A window should open up with the two folders labeled Disk 1 and Disk2. Double-click on Disk 1. Double-click on the Installer icon, then click Continue. Click on Install. After the system has finished installing files you will be prompted to restart your Macintosh. Make sure your printer is ON, and click Restart. After restart, go to the Chooser and for a serial connection select the Stylus COLOR (EX) printer icon. Select the port. Disable Background printing. Close the Chooser. If you must use Background printing, your system must have a minimum of 6MB of unused RAM that can be dedicated to the EPSON Monitor2 and your operating system. If you are using Background printing, go to the EPSON Monitor2, go to File and select Get Info. Change the Minimum amount setting to 2000 and the Preferred amount setting to 3000, then close the EPSON Monitor2.
What do I need to do to print with my Stylus printer on a LocalTalk or EtherTalk network?
To use the printer on a LocalTalk network, install the optional LocalTalk Interface (C823121). For EtherTalk install the optional Ethernet Interface (C823461). Set the AppleTalk/Network Control Panel to Modem/Printer port (LocalTalk with older OS versions) for for the LocalTalk interface and Ethernet/EtherTalk for the Ethernet interface. Enable AppleTalk in the Chooser and run the Epson Namer utility and give the printer a unique name to easily identify the printer on the LocalTalk network.
Whenever I try to print from my Macintosh, I get a type 11 error, my system locks up or a portion of my image doesn't print. What's wrong?
These issues are typically memory related errors. Check the available memory and its allocation. You may need to increase the memory allocation for your application, the EPSON Monitor, or both. Insure that the needed system resources are available. If you have background printing enabled, you may want to try disabling it. Some printing issues can also be caused by conflicts with Extensions and Control Panels. Turn off all third party Extensions and Control Panels that have been added to the system and restart.
When printing from my Macintosh an error message comes up that says "The printer is not responding, ensure the printer is connected and on-line. Would you like to try again?". What should I do?
If your system version is 7.5.2, 7.5.1 or 7.5 and your computer is a PowerMac6100/60, PowerMac6100/66, PowerMac7100/66AV, PowerMac7100/80AV, PowerMac7200/90, PowerMac7200/120, PowerMac7500/100, PowerMac7600/120, PowerMac8100/80, PowerMac8100/80AV, PowerMac8100/100, PowerMac8115/110, PowerMac8500/120, PowerMac8500/132, PowerMac8500/150, PowerMac9500/120, PowerMac9500/132, PowerMac9500/150, Centris660AV, Quadra840AV the file SerialDMA Ver.2.0.2 should be installed in the extensions folder. To check whether SerialDMA Ver.2.0.2 is installed in your system, open the system folder and the Extensions folder, then check whether it is installed. To check the version number of the file, click the file and select Get Info from the File menu. If SerialDMA Ver.2.0.2 is not installed, drag it onto the Extension folder of your hard disk. The system will remind you that extensions need to be placed in the Extensions folder; click OK and SerialDMA Ver.2.0.2 will be copied. After the extension is in your system, you need to restart your Macintosh. Also, the Serial Port Arbitrator that ships as part of AppleTalk Remote Access conflicts with SerialDMA Ver.2.0.2 when running on Macintosh 7200, 7500, 8500 and 9500. Remove the Serial Port Arbitrator from the Extensions folder if installed. Also, verify your system meets the minimum system requirements.
What Macintosh computer systems are compatible with the printer?
You can use any Macintosh or Power Macintosh model except the Macintosh SE/30, Macintosh LC, Macintosh Plus, Macintosh 512K, Macintosh 128k, Macintosh IIfx, Macintosh +, Macintosh 512, Macintosh Classic Series, Macintosh Portable, Macintosh SE, or PowerBook 100. System 7.1 or higher is the required operating system, at least 8MB of RAM (16MB or more is recommended), at least 20MB of free hard disk space for storing images (40MB or more is recommended), VGA (8 bit, 640 x 480) or better display and monitor, and a standard Apple System/Peripheral-8 cable or equivalent. Cables can be purchased through EPSON Accessories. The part number for a 6-foot cable is F2V024-06 or a 10-foot cable is F2V024-10.
Can I use this printer on an AppleTalk or Ethernet network?
Yes, the Stylus COLOR 800 is designed to run on either type of network when an optional interface board is installed. The LocalTalk (C823121) and Ethernet (C823461) are compatible with the Macintosh environment.
I installed the printer driver on my Macintosh, but it isn't showing up in the Chooser. What went wrong?
The EPSON driver does not support QuickDraw GX. Therefore, this feature will need to be disabled. If your using system version 7.5 or later disable this feature, go to the Apple menu, select Control Panels, then open Extensions Manager and de-select "QuickDraw GX." After restarting, the printer will appear in the Chooser. If Quickdraw GX is off and there is still no printer icon in the Chooser, verify your system meets the minimum system requirements. Refer to your User's Guide for more information.
Whenever I power up my Macintosh the printer switches from the printer port to the modem port. How can I correct this?
Update your driver to the latest version. A alternate solution is to make sure AppleTalk is inactive in the Chooser. Go to the Extensions Manager and disable Apple Share, File Share, and Printer Share. Open Preferences and drag the AppleTalk, File Share, and Printer Share preferences to the trash. Restart the Macintosh and go to the Chooser. In the Chooser set any other unused printers on the printer port, then set Stylus Color on the printer port and confirm it. Restart the Macintosh again and check to see if the printer driver stays on the printer port.
The ColorSync option of the EPSON Macintosh driver is grayed out. Why can't I select it?
ColorSync must be active to select this option in the driver. Enable ColorSync in the Control Panels section of the Extensions Manager and restart.
Sometimes I get garbage when printing from my Macintosh. Other times the printer will not print anything at all. What's wrong?
Your Spool Folder, which is opened every time you send a job, may be holding too many files. If there are files being held in this folder, you may have trouble printing. To check the Spool Folder, open your hard drive, go to the Systems Folder, then go to Extensions. In Extensions, open the EPSON Folder, then open the Spool Folder. If there are held jobs, trash the entire folder. Empty the trash and try printing again. This normally resolves the issue. Also, check the Chooser and confirm that AppleTalk is inactive if the printer is connected to the printer port.
I have the printer connected to my PC and my Macintosh. It prints fine from the PC. Why won't it print from the Macintosh?
Print the Default Settings (Color Cleaning + Power-On) on the printer to verify that the I/F mode is set to Auto, not Parallel. The Auto setting allows the printer to automatically switch between the parallel, serial, and optional interfaces. If printing from both the PC and Macintosh, you may also want to consider changing the Auto I/F wait time to 30 seconds (default is 10 seconds). This sets the time period for the printer to wait for data from the current interface and not accept data from the other interface.
When printing from my Macintosh I always get a type -39 error. What should I do?
Make sure that the printer is functioning normally by running a printer test page. If the test page prints fine, but you still continue to get the error from the Macintosh, you may need to upgrade your System software. If you are running System 7.5.2, we would suggest that you upgrade to System 7.6.1 or higher. This is also suggested by Apple.
I installed the printer on my Macintosh , but when I close the Chooser I get the error "Cannot identify your printer correctly. Make sure your printer is on and properly connected. Then use the Chooser to select the printer and port". What should I do?
Check to make sure the printer in on-line and ready to receive data. The printers power light should be on solid. Confirm that the Chooser port and the port on the printer are the same and the cable is connected at both ends. Make sure the cable is a serial cable, not an AppleTalk cable. Remove switch boxes or any other devices that are part of the connectivity, so the only connection between the printer and the Macintosh is the serial cable. Try to select the printer again. If the problem persists, there may be an extensions conflict. Set the computer for minimal system extensions and enable the printer driver, restart the system and try to select the printer again. Also, the driver may have become corrupt. You will need to remove and reinstall the driver. To remove the driver, save any open files, then exit all applications. Open the Hard Disk, the System Folder, then the Extensions folder. In the Extensions folder, find the Epson Folder, the Epson Monitor2, the EPSON Stylus (EX), and the EPSON Stylus (AT) files. Drag the folder and the three files to the trash, then empty the trash. The driver files have now been removed. Restart the Macintosh while holding down the Shift key (starting with Extensions off). If your reinstalling the driver from a CD-ROM, leave the "Apple CD-ROM" extension enabled. After the Macintosh restarts, reinstall the printer driver. If there is still a problem, verify your system meets the minimum system requirements.
I already selected my printer in the Chooser. Why am I getting a message saying, "Sorry Stylus Color can't be used"?
This message indicates that there is something wrong with the driver or the way it was installed. This usually occurs when you have a system crash while printing due to low system resources (not enough memory). When this happens, the driver is corrupted and therefore thinks that the printer is not available. You will need to remove and reinstall the driver. To remove the driver, save any open files, then exit all applications. Open the Hard Disk, the System Folder, then the Extensions folder. In the Extensions folder, find the Epson Folder, the Epson Monitor2, the EPSON Stylus (EX) and the EPSON Stylus (AT) files. Drag the folder and the three files to the trash, then empty the trash. The driver files have now been removed. Restart the Macintosh while holding down the Shift key (starting with Extensions off). After the Macintosh restarts, reinstall the printer driver.
Can I connect the printer to both a PC and to a Macintosh?
Yes, both the serial and parallel interfaces can be connected to host computers. We recommend that you do not send print jobs from both computers at the same time. Some programs may send a partial print job to the printer and then pause for further processing. When it pauses for further processing, the printer's port may time-out and the printer may start to receive data from the other computer before the previous print job is complete.
The power light is on, but nothing prints.
Make sure the printer cable is connected. Turn off the printer and computer. Make sure the printer cable is securely connected to the printer and computer ports. Turn on the printer and try printing again. If the cable was not the issue, turn off the printer and computer, disconnect the interface cable and run a self-test. If the self-test works, check the application software for correct installation. Make sure your computer has enough memory to handle the data in your print file. You may want to try reducing the resolution of your image, select fewer colors, or add more memory to the computer. If you are still having difficulty printing and you are using Windows, try checking the Spool Manager to see if it is on hold or if there are stalled print jobs. If you are using a Macintosh, make sure your Spool Folder is empty. If the printer sounds like it is printing, but there is no ink on the paper, The print head nozzles may be clogged. From the Utility section found in the EPSON printer driver, clean the print heads by performing a head cleaning followed by printing a nozzle check pattern. A head cleaning and nozzle check must be performed as a cycle. After printing a nozzle check, examine the printed dot pattern. Each staggered horizontal and straight vertical line should be complete, with no gaps in the dot pattern. If there are gaps in the dot pattern, continue with another cycle. Perform up to 6 cycles if necessary. If the nozzle check is not printing completely, and if the head cleanings do not help the nozzle check pattern to print completely, try replacing the ink cartridge.
How can I increase my print speed?
Is your using single sheet paper to print, check that the printers blue paper thickness lever is set to single sheets, not envelopes. One thing to keep in mind is that color print jobs can produce 20-100 times as much data as a monochrome (black/white) text print, which makes color printing a heavy draw on your CPU, memory, and hard disk. The entire printing process includes the time it takes the to spool the job into the spool directory or folder. Increasing or maximizing physical RAM, lowering the print resolution, and enabling "High Speed" in the driver will also help speed up the process. Ensure that you have at least 150MB of free hard drive space available. On a PC creating a unique spool directory improves printing performance by eliminating spooling conflicts within Windows. Regularly defragmenting (DEFRAG) your hard drive In the Control Panel will also help. Also in Control Panel, Printers, click on Connect and disable "Fast printing direct to port". If you using a Macintosh disable background printing in the Chooser. If you must use Background printing, allocate more memory to the Epson Monitor. To increase the speed when printing black text only, set your printer driver to the Black ink option, try setting the Print Quality to Economy, turn MicroWeave off and High Speed on, and choose No Halftoning.
Why am I getting error messages when printing?
If you are using Windows, conflict error messages or slow printing may be caused by temporary files in the EPSON Spool Manager temporary file directory. Make sure your spool directory does not contain any files with the "jnl" extension. Also, you may want to try creating a new spool directory. To change the spool directory, you will first need to make a unique directory on your hard drive, such as C:\SPOOL. Then, open the Spool Manager and make sure the EPSON Stylus COLOR 800 is selected. Click on Options, select Default Spool Directory, change the directory to the new directory you created, and click OK. Click on Queue, select Setup, and make sure the spool directory changed to the new unique directory. Make sure the box for "Use Print Manager for this port" is not checked, then click OK. Close the Spool Manager, restart the computer and try printing again. If you are using a Macintosh, make sure the Spool Folder is empty.
What does the EPSON StatusMonitor do?
The EPSON StatusMonitor allows you to check the level of ink in the printer and to control the way your software warns you about printer issues. Choose Print from the File menu or click the Print button in your application to see the printer settings dialog box. Click the Utility button to get the Utility menu. Click the Status Monitor icon. The software checks the amount of ink remaining in the printer and displays the Status Monitor window. If you want to change printer messages and warnings, click the Configuration button. Choose the options you want and click OK to save the settings.
I removed the white label from the top of one of my ink cartridges. What should I do?
Do not install the cartridge. If you have already installed it and the printer is printing correctly, change the cartridge immediately. If you have already installed the cartridge, or if a previously installed ink cartridge was missing its white label at the time it was installed, and now the nozzle check will not print completely even after running cleaning cycles, your printer may need a service.
The quality of my printed output is unacceptable. What can I do to improve this?
Verify that you are using the correct printer driver for your printer model. Make sure that the printer's paper adjust lever is set to 0 for regular paper and + for envelopes or thicker media. If MicroWeave is off, turn this feature on. If High Speed is on, turn it off. Make sure the Media Type setting matches the paper or media loaded. Also, the Halftoning and Color Adjustment Mode options may be set incorrectly for your document type. Let the printer driver automatically select the settings for the best quality. The paper you are using may be damaged, old, dirty or loaded incorrectly. Remove the paper and reload a new stack ensuring that the printable side is face up. If your output is faint, check the printer driver to make sure you have selected a print resolution other than Economy. For vertical banding, rough or grainy images run the Print Head Alignment utility to align the print heads for precise vertical lines. If the image does not contain the colors you expected, the color settings on your application software may need adjustment. Refer to your software documentation for help on adjusting colors. If the previous steps do not resolve the issue, the print head nozzles may be clogged. From the Utility section found in the EPSON printer driver, clean the print heads by performing a head cleaning followed by printing a nozzle check pattern. A head cleaning and nozzle check must be performed as a cycle. After printing a nozzle check, examine the printed dot pattern. Each staggered horizontal and straight vertical line should be complete, with no gaps in the dot pattern. If there are gaps in the dot pattern, continue with another cycle. Perform up to 6 cycles if necessary. If the nozzle check prints completely, and you're still experiencing a problem, make sure you are using the most current version of the printer driver. You can obtain the latest printer driver from the EPSON web site. The resolution of your image may also be set too low. Increase the image resolution using your image-editing software, or decrease the size of the image. Another troubleshooting test to try is moving the printer to another computer. This will eliminate the possibility of a defective printer cable, parallel port, or software issue. If your still experiencing a problem try replacing the ink cartridge.
My printouts are missing color and/or black print. How can I resolve this issue?
If the printer is printing blank pages, make sure you are using the correct printer driver and make sure the paper size is correctly selected in the driver. If the printer is printing black only, the Ink option in the printer driver may be set to Black instead of Color or a setting in the software may be set to print black only. Also, the print head nozzles may be clogged. From the Utility section found in the EPSON printer driver, clean the print heads by performing a head cleaning followed by printing a nozzle check pattern. A head cleaning and nozzle check must be performed as a cycle. After printing a nozzle check, examine the printed dot pattern. Each staggered horizontal and straight vertical line should be complete, with no gaps in the dot pattern. If there are gaps in the dot pattern, continue with another cycle. Perform up to 6 cycles if necessary. If the nozzle check is not printing completely, and if the head cleanings do not help the nozzle check pattern to print completely, try replacing the ink cartridge.
Why are my margins incorrect?
The paper may be loaded incorrectly. Make sure that the left and right edge guides are flush against both sides of the paper. Make sure the margins are set correctly in your software application, and make sure you are not trying to print outside of the printable area of the page for your paper size (printable area of the page specifications are available in the User's Manual). Make sure the correct paper size is selected in the printer driver settings. Also, check the settings on the paper menu in the printer driver to make sure they are correct for your paper size. Margins are not adjustable via the printer.
Will the printer print 360, 720, and 1440 x 720 dpi on plain paper?
The Stylus COLOR 800 can print 360 x 360 dpi and 720 x 720 dpi in color and monochrome on plain paper. The 1440 x 720 dpi option should not be used when printing on plain paper. When printing 1440 x 720 dpi, use the EPSON coated or glossy paper.
What is the correct way to load transparency paper?
Insert the EPSON transparency sheet making sure that the notch is at the top right side of the sheet when facing the front of the printer. Please refer to your User's Guide for detailed information.
If I want to clear the printer's memory, what should I do?
Make sure that you cancel the print job from the computer before you try to clear the printer's memory. After canceling the print job, turn the printer off. Wait a few seconds, then turn on the printer.
The black or color Ink Out light is flashing or on solid.
If the light is flashing, the ink supply is getting low and you will need to replace the cartridge soon. If the light is on solid, the ink cartridge is completely empty and will need to be replaced in order to continue printing. Make sure you only remove the yellow tape seal from the top of any ink cartridge you install into the printer. If the white label has been removed from the ink cartridge, the cartridge will not function correctly and it needs to be replaced. More importantly, to avoid potential damage to the printer, do not install the cartridge if the white label has been removed.
When I installed new ink cartridges the printer does continuous cleaning cycles. Is there something wrong with my printer?
The first time a ink cartridge is installed in the printer, it will take 7-9 minutes to charge the ink system and initialize the printer. While the ink is charging the power light will flash. NEVER turn off the printer while the power light is flashing. When installing replacement ink cartridges, the printer will take approximately 4 minutes to charge the ink. These initialization times are due to the superior technology of EPSON's piezo print head, the number of ink nozzles in the print head and on a new printer the protective lubricant placed in the print head during the manufacturing process. This initialization is a normal and necessary process. If you turned off the printer during the initial ink charging cycle because I thought it was taking too long, power the printer back on and allow the printer to perform the complete charge of the ink delivery system.
Why won't the printer feed paper?
Power the printer on and press the Load/Eject button to see if paper will load. If no paper loads, make sure the paper isn't curled or creased, it isn't too old, isn't loaded above the arrow on the left edge guide, and that the paper isn't jammed in the printer. Reload the paper making sure the paper edge guide is adjusted to fit the paper's width. If the Paper Out light is on solid or flashing, power the printer OFF and remove the printer cable. Make sure all the packing materials are removed. If the problem persists, the printer may need to be sent in for service.
Why is the Power light still flashing even though the printer has finished charging the ink cartridge?
The ink cartridge clamp isn't locked down. Press down on the clamp to lock it. Make sure that all packing material has been removed from the inside of the printer (follow instructions on the notice sheet). If the printer does not move or make any noise for more than 5 minutes, turn off the printer. If the light is still flashing when you turn it back on, the printer may need to be serviced.
How do I calibrate my printer?
To align the print heads, make sure that paper is loaded and the printer has power. Access the Utility tab (Windows) or Utility button (Macintosh) located in your printer driver settings. Click the Print Head Alignment icon and follow the instructions on the screen to print a test page and select the correct alignment.
All lights are off. Why won't the printer initialize?
The printer may not be receiving any power. Turn the printer off. Remove the interface cable from the back of the printer, unplug the power cord, plug it back into the outlet, and try turning the power on again. If you still do not get power to the printer, try another outlet. Make sure the outlets you are connecting to are not controlled by a switch or timer and are able to operate other equipment.
Can I use sheet labels with this printer?
Yes, EPSON makes Photo Quality Self Adhesive Sheets. To avoid paper jams, only load one Photo Quality Self Adhesive Sheet at a time. Also, set the Media Type in the printer driver to the "Photo Quality Ink Jet Paper" setting.
Calibration doesn't seem to have any effect. What should I do?
Make sure that whenever you turn off the printer, you are always using the printer's power button. Never use an external switch, such as a power strip, surge protector, or power protector, to turn off the printer. If you turn the printer off using an external switch, calibration settings will not be saved.
Is the printer Year 2000 ready?
Yes, the printer is Year 2000 ready.
Is there a PostScript driver available for this printer?
Yes, EPSON has an optional Adobe PostScript Level 2 driver with Pantone approved colors. The software, called EPSON StylusRIP, is fully compatible with all leading graphic software applications and is available through EPSON Accessories.
How do I find the serial number for Photo Deluxe ?
The serial number is printed in the ColorPak jumpstart guide but only in the Macintosh section.
Parallel Port Scanners
Sometimes Epson printers have problems working with Parallel port scanners, as the scanner software will conflict with the Epson printer management software. To disable the Epson software,
When I print from Appleworks 5.0.3 / 5.0.4 or Word 98 from my Macintosh (PowerMac / G3 / G4 / iMac / DV iMac) to my EPSON Stylus Color/Photo inkjet printer, some of the text is cut off on the right edge. What can I do to correct this?
Follow the steps below to correct the issue of characters clipping from Appleworks and Word 98.
1) Open document.
1) Open document.